Showing posts with label PTFE bearings. Show all posts
Showing posts with label PTFE bearings. Show all posts

Monday, July 27, 2015

Lubring (Turcite-B®) – Special Notes on Bonding and Finishing

As a globally reputed manufacturer of Lubring Slideways (Turcite-B®), we are frequently asked to provide technical assistance with regards to the bonding and finishing of the material.
Lubring is a slideway bearing material that is used primarily in machine tool building and reconditioning. As such, the machine builder is usually equipped with enough knowhow on the bonding and subsequent planing of the material, such that it forms the most effective bearing surface. However, we often supply to dealers or first time builders, who need more assistance on the bonding process.


Preparation:
The metal surface to be mounted with Lubring Slideway can be prepared by the normal machining methods such as, grinding, milling, shaping, and planning. The surface roughness of all forms of preparation should be preferably between Ra = 1.6 µm and Ra = 3µm and not more than Ra = 6µm.
Once roughened the surfaces can be cleaned with Trichloroethylene, Perchloroethylene or Acetone. Slideway bearing material should be cleaned similarly.
Bonding:
For bonding of Lubring Slideway the following resin adhesive can be used: Ciba Geigy’s Araldite – Hardener – HV 953U; Araldite AW106. The Araldite should be applied both to metal and slideway and be spread as uniformly as possible by means of a serrated spatula. To obtain the best dispersion of the adhesive, when spreading on the slideway brush in the longitudinal direction; when spreading on the metal, brush in the transverse direction. The total quantity of bonding should be approximately 200gm per sq. mt.
Hardening:
After mounting the slideway a clamping pressure of between 0.1 – 0.3 kp/sq.cm is recommended. It is important to keep the pressure constant during the hardening process. Due to the differences in the thermal expansion coefficient of the materials, maximum curing temperature should not exceed 40°C. The hardening time for various temperatures is: 20°C min 15 hours; 25°C min 12 hours; 40°C min 5 hours.
Finishing:
After curing of the adhesive, the Lubring Slideway can be machined by conventional means. The choice depends on the machinery available viz.: grinding; grindstone.
Grinding: For grinding of Lubring Slideway use the same speed as grinding cast iron, taking care that sufficient cooling is used with an ‘open ’stone. The grindstone should be preferably silicon carbide based with rubber or polyurethane binding; grain size 80-30. Alternatively aluminum oxide with rubber bonding may also be used for soft, fine grinding action, pre-polishing and pre-mating treatment.
Oil Grooves: Lubring Slideway can be machined with oil grooves using the same methods and cutting data as used for cast iron. The form and depth of the oil grooves are optional. However, the oil grooves should never pierce through the Lubring Slideway. Oil grooves should be away from the edges by 6mm.
Metal Mating Surface: The metallic mating surface running against the Lubring Slideway should be finished to 16 Ra for optimum performance. The surface finish must never be below 14 Ra or above 20 Ra as applicable to cast iron or steel. This surface finish should be obtained by grinding in the direction of travel. Do not lap or polish to obtain this surface finish.


The above parameters provide an effective guideline not just for Lubring, but for bonding all PTFE-related items to metal.

Friday, August 30, 2013

PTFE Sliding Bearings: Calculating Coefficient of Friction

PTFE is a preferred material in sliding bearings for three very specific reasons:
  1. Load bearing capacity
  2. Weather ability (due to its overall chemical inertness)
  3. Low coefficient of friction
The first two factors are well accepted and easily tested. The vertical load on a bearing is simply tested by placing the bearing under a hydraulic press of suitable capacity, applying 1.25 times the rated load of the bearing and holding this load for a period of 1 hour to observe any adverse impact on the bearing material. In our own experience, it is very rare that pure PTFE would fail in this instance, since:
  1. Pure PTFE genuinely does have a very high load capacity and even in the event of over-loading, would tend to deform rather than break down
  2. The design load for most bearings incorporates a safety factor of up to 60% – implying that while PTFE may be able to withstand a load of up to 40Mpa, it is designed with a load of only 16Mpa and is thus well within its own capacity to take the load applied
Weather ability is difficult to test, as this is a long-term guarantee that the material can stay in outdoor conditions without experiencing any degradation in properties. However, most clients are happy to take this assurance at face value – as long as they can satisfy themselves that the material being used is in-fact pure PTFE. Its should be mentioned here that in the event that reprocessed or recycled PTFE is used in sliding bearings (a gross violation of quality norms, but one that may occur all the same, especially if the bearing manufacturer is buying their PTFE from a third-party and is therefore not directly in control of the quality), there will definitely be a failure of the bearing after installation.
As mentioned in earlier articles, we have witnessed many deviations from expected performance when presented with reprocessed PTFE. Amongst these is the tendency of the material to become brittle and even crumble after being kept outside for a prolonged period (usually over a few months). No doubt, a similar effect would be experience by a material used in a bearing that is installed on a bridge or flyover – with the result that the bearing may fail after only a year of service.
Coefficient of friction
The problem with the coefficient of friction is that most people are not fully familiar with what it implies. So let us start with defining it and then look at the misassumptions surrounding it.
The coefficient of friction between two planes is defined as the ratio of the force needed to move one plane over the other divided by the force pushing the two planes together.
So in the case of a block resting on a table, coefficient of friction between the block and table would simply be the force needed to slide the block across the table, dived by the weight of the block itself.
Coefficient of Friction PTFE (1)
Since the coefficient is a ratio of two forces, it does not have any units. A common mistake clients make is to ask us to define the unit we have considered for the coefficient of friction.
In the case of the PTFE sliding bearing, the coefficient of friction being considered is that between PTFE and polished stainless steel. Here again, a mistake is often made asking what the coefficient of friction of PTFE is. There is no such thing as a stand-alone value for coefficient of friction for any material. The coefficient between PTFE and polished stainless steel will no doubt be much lower that between PTFE and concrete. In other words, it would take more force to move a slab of PTFE across a concrete surface than it would to move the same slab across a polished stainless steel surface. Thus, when we talk about a coefficient of 0.04 between PTFE and stainless steel (the commonly accepted value for bearing manufacturers), we are saying that for a 1Kg PTFE block to slide across a polished stainless steel surface, it would require only 40 Grams of horizontal force. (Note: we are aware here that Kgs and Grams are units of mass and not force, but seeing as these are ratios of force, the values in Kgs/Grams against the values in Newtons would yield the same results).
Measuring coefficient of friction
We have already described that the value for the coefficient is derived by dividing the horizontal force over the vertical force. However, in practice, this is less straightforward. We would like to look at some of the methods that are used around the world to check these values as pertaining specifically to PTFE bearings, before describing what we feel is the most straightforward and easily implemented method.
  1. Two-press method
    It is not possible to test the bearings simply by applying a vertical load and seeing at what horizontal load the bearing slides. This is because the bearing plate on which the horizontal load is applied also has another surface, which would be in contact with the vertical press and therefore be subject to friction from the press itself (which is likely to be very high).
    Therefore, the accepted method is to place 2 bearings, back-to-back (shown below) and exert load on the centre.
    This process is technically sound, but practically not always feasible. For starters, the bearing shape itself may not lend itself to being places back to back. It may have welded guides attached to it or be of an unusual shape. In addition to this, the process in expensive – requiring two hydraulic presses.
  2. Load indicator method (laboratory)
    In this method, the stainless steel plate is placed horizontally with the PTFE plate on top. The PTFE plate is connected to a steel wire which is in-turn connected to a load indicator. The load indicator has a motor, which causes it to move upwards very slowly. As the indicator moves up and the wire gets tight, the load reading starts to show the horizontal load being applied. Once the PTFE plate starts to move, the reading is recorded and divided by the weight of the PTFE plate to give the coefficient of friction.
    This method is possibly the most accurate, as load indicators can offer values in grams. However, it again suffers from the issue that if the bearing plates are not totally flat or are too big for the equipment, they cannot be accurately tested. Furthermore, it is debatable whether such accuracy is needed in the realm of sliding bearings
  3. Poly Fluoro method (inclined plane)
    In an attempt to find a quick, repeatable, logical and universally applicable method to check the coefficient of friction, our method follows the rather simple process of gauging the angle of incline.
    For starters, we do not believe that getting an accurate value of the coefficient of friction would add any value to the product. If we can confirm that the plates slide at a coefficient of friction set to 0.04, then it does not matter whether the coefficient is in-fact 0.03 or 0.036, as the product has met its required specification.
    Coefficient of Friction PTFE (2)
    The diagrams  show that when the planes are inclined, the coefficient of friction takes the value of the tangent of the angle of inclination. This allows us to easily check the coefficient of friction, as we simply set the ratio of Y to X to equal 0.04 and check if the PTFE plate slides down the plane, when placed on the SS plate. Again – note here that only in the event that the PTFE plate does not slide, can we conclude that the coefficient is greater than 0.04 (and hence outside tolerance). Whether the plate slides slowly or very fast, is of no consequence – as either way it confirms that the coefficient is at least 0.04.
    Coefficient of Friction PTFE (3)
    In the event that the client specifies a higher or lower coefficient, the same method can be employed, by simply changing the value of Y. So we first assess what the value of Y should be by multiplying the length of the bearing plate by 0.04 and then use a calibrated slip gauge to prop up the bearing on one side (preferably on a flat bed) so that the angle is attained.
    The method employed here is useful to check PTFE bearings as it can be applied to any design and multiple bearings can be checked from one lot if needed, without the hassle of making separate fixtures and modifications. Furthermore, it can be checked even before the bearing is assembled so as to confirm that the PTFE material being employed meets the parameters.
Static vs Dynamic coefficients
It must be mentioned that both static and dynamic coefficients of friction are relevant metrics and that the inclined plane method only measures the static coefficient. However, this is of no concern for PTFE bearings as PTFE is known to exhibit nearly identical values for both static and dynamic coefficients (a property unique to PTFE and not universally applicable).
We believe that the method described above is a more effective way to check for a very important parameter that bearings are based on.

Monday, July 4, 2011

Cantilever Load Considerations for PTFE Sliding Bearings

We have shifted to www.polyfluoroltd.com/blog - do follow us there

As a manufacturer of sliding bearings in India, one of the challenges we face is that there does not exist an official book of guidelines specifically for this type of bearing. The closest we have is the IRC:83 – which is the code book for POT-PTFE bearings, and which details the specifications of the materials to be used and also the testing parameters for POT bearings. As such the IRC:83 does provide some guidelines – but does not address the finer design requirements for sliding bearings. Consequently, during design and testing of the bearings, customers rely on the Quality Assurance Plan (QAP) we provide them, with the option to question, refute and even modify the requirements as they see fit.

Although the BS:5400 and AASHTO standards do make specific recommendations for PTFE sliding bearings, customers are not always willing to accept their parameters as they may sometimes vary from those specified in the IRC – in places where the codes overlap. This can result in technical stand-offs, between the customer and manufacturer, as each tries to convince the other regarding a certain process or parameter, without any official rule book, to back up their view point.

Among the more interesting technical debates we have had recently has been regarding the thickness of the top plate (upper sole plate) in bearings with high movement requirements.

Given a specified vertical load, a PTFE sliding bearing will be required to have a PTFE pad with side determined by the compressive strength of PTFE (usually taken at 100-200 Kgs per sq. cm). This side in turn determines the side of the lower sole plate. Give these two dimensions, the movement of the bearing (specified usually by the client/ contractor) will give us the side of the Stainless Steel sliding element, which in turn will give us the side of the upper sole plate.

Our designing of PTFE sliding bearings began with taking standard designs for specified loads and movements (such as C&P) and recommending them to clients. As we became better versed with PTFE sliding bearings, we started designing from scratch – using the parameters of movement, load and rotation to design customized PTFE bearings for specific project requirements. As many of the original standard drawings recommended sole plates of 12-15mm thickness for bearings up to loads of 50-65 Tonnes, we too continued with this recommendation. After all, the constraint of a bearing in taking a vertical load depends purely on the PTFE – as when compared with steel, PTFE has a much lower compressive strength (100-200 Kg per sq. cm versus steel’s 14000-15000).

It came as a surprise to us therefore when a client expressed concern over the top plate thickness – citing that the bending moment caused by the vertical load would be in excess of what the top plate could accommodate, given the overhang of the top plate over the bottom. This led us to revisit a lot of the standard designs – only to find that for similar load-movement parameters, other bearing designs did not recommend a thicker sole plate that our customer was insisting on.

We therefore went back to theory to gauge exactly how much of a bending moment would be caused by our given load and assess whether there was a case for changing our top plate design.

The formula for calculating the bending moment is as follows:

M= (P x L2)/2

Where:

P = Pressure (Kg/cm2)
L = Length of overhang (cm)
M = Maximum Bending Moment (Kg)

Once we know M, we divide by the Maximum Allowable Bending Stress (S) of the material (1650Kg/cm for steel) – to derive the thickness of the steel plate required.

In the example in question, the value of M obtained was 3941 Kgs, which when divided by S gave a thickness of 3.78cm – or 38mm.

This was a shocking revelation, as our recommendation was for 15mm – clearly insufficient for the load in question. Nonetheless, we wanted to dig deeper to find out how most standard bearing designs only called for a 12-15mm thickness – when the theory clearly showed that this was inadequate.

In most of our discussions with consultants and industry experts, the value of 38mm was ratified and we were told that this was in fact the thickness needed. They were unable to explain, however, why the standard designs did not tally with the theoretical calculations. Our question was finally answered when we spoke with a contractor who studied the drawings and design details and confirmed that while a thickness of 38mm was indeed required, the thickness of the insert plate also needed to be taken in to account.

The insert plate is installed at site and is simply a 25-30mm thick steel plate grouted/ cast along with the concrete substructure and/or superstructure. The bearing is welded or bolted to this plate and the load on the bearing is transferred through the plate as well. Thus, a bending moment will act through the layers of both the upper sole plates and the insert plates – meaning that even with a sole plate thickness of 15mm, the total thickness through which the load acts is 40mm – which is more than sufficient in our example.

We went back to our client with this, but were informed that they were not using an insert plate in this particular project and that the sole plate thickness needed to be at least 40mm as per our calculations.

The exercise was an eye-opener, because we had never before been questioned on the bending moment for sliding bearings, nor had we come across any design calculations for this in the various codebooks. However it is a critical point in the design of a PTFE sliding bearing – as there is always an overhang of top plate over the bottom. As a rule, one needs to verify that an insert plate is being used and of what thickness it is. Adding this thickness to the sole plate thickness, the designer needs to verify whether the bending moment is being accommodated. If not, the thickness of the upper sole plate must be re-worked.

Tuesday, June 14, 2011

The wonder that is Lubring (Turcite®)

We have shifted to www.polyfluoroltd.com/blog - do follow us there

It is only rarely that a marketing push succeeds so thoroughly that the brand name becomes synonymous with the product itself. When Turcite B ® was first introduced, PTFE itself had been around for quite a while. Yet, so effective was the branding of this variant of PTFE that everything from the properties, to the composition to the colour merged under a single umbrella and became known simply as “Turcite ®”. The material itself has become a mainstay in the industrial goods market with machine tool builders, re-conditioners and bearing manufacturers demanding it for their applications.
As the market expanded, new manufacturers developed their own variants under different brand names (ours being Lubring), which all succeeded in their own way. However, to this day, clients will initially demand “Turcite ®” – following which there will be a brief discussion about the fact that our material is equivalent to Turcite ®, but that we brand it under a different name. Usually the client is happy as long as the properties match and that the colour of the material matches the turquoise-green shade developed specifically for Turcite ®.
We want to take a closer look at this material, because despite it’s widespread usage, there are always questions from clients regarding the application and installation of this material. We will look at the following aspects:
  1. What is Turcite ® (Lubring)
  2. Where can it be used? What are the possibilities and limitations?
  3. How must it be installed?
What is Turcite ® (Lubring)?
Quite simply – Turcite ® is PTFE impregnated with fillers and additives that serve to enhance the wear properties of the material. It is used, most often in a sheet form, in thicknesses ranging from 0.5mm (0.02”) to 4mm (0.16”), although in some applications, it is also used as a bush and in more rare applications it is used as a thick plate.
Being based on PTFE, the material cannot be extruded like a normal plastic sheet and instead needs to be “skived” – the process most commonly used to make thin PTFE sheets (See: PTFE – Myths Busted!). Also, the material will not easily adhere to other surfaces – another feature resulting from its PTFE base. Therefore a chemical etching is required on one surface of the material, so the sheet can be bonded to other articles.
In a broad sense, Turcite ® (Lubring) offers the following key advantages:
  • Very low friction for reduced power loss
  • No stick-slip for positional accuracy / control
  • Good specific bearing loads
  • Low wear for long life
  • Excellent chemical resistance / fluid compatibility
  • Unlimited shelf life
  • High temperature resistance
  • Absorbs vibration during machining

Applications of Turcite ® (Lubring)
Most commonly, Turcite ® (Lubring) has been used in the machine tool industry where it serves to either replace or reinforce standard phosphor-bronze LM guideways. The material was earlier used primarily to recondition old machines in which the guideways had worn out. However, increasingly it is incorporated in new machines as well – owing to the higher life and lower maintenance required in comparison to metal guideways.
As mentioned above, Turcite ® is also used as a bush – which needs to be specially moulded and machined as per the customer’s requirements. These bushes are usually replacements for metal bushes – especially in areas where the lubrication of the metallic bush is as issue. Turcite ® – and in fact all PTFE grades – has self lubricating properties which means it can function deep within a sub-assembly taking enormous wear loads and does not need to be lubricated constantly to avoid damage.
However, the material is not an out-and-out replacement for metal. Being PTFE based, the material has a compressive strength limited to 150 Kgs per square cm (2,200 psi). This means that a single square foot of Turcite ® can accommodate a load of up to 150 Tonnes – which is more than sufficient for most applications. However, it is also a soft material (Shore D Hardness: 50-60) – meaning that point loads and excessive squeezing of the material can cause deformation.
Another limitation is with regards to insulation. Although the material has excellent temperature resistance (up to 260 Degrees Celsius/ 500 Fahrenheit), it does not have any electrical insulation.
In all, the industries for which we have supplied Turcite ® (Lubring) include:
  • Automotive
  • Machine tool
  • Infrastructure
  • Nuclear power
  • Casting and forging
  • Textiles
  • Pumps and valves
  • Pipe liners
Installation guidelines for Turcite ® (Lubring)
Preparation: The metal surface to be mounted with Lubring can be prepared by the normal machining methods such as, grinding, milling, shaping, and planning. The surface roughness of all forms of preparation should be preferably between Ra = 1.6 µm and Ra = 3µm and not more than Ra = 6µm. Once roughened the surfaces can be cleaned with Trichloroethylene, Perchloroethylene or Acetone.
Bonding: For bonding of Lubring the following resin adhesive can be used: Ciba Geigy's Araldite - Hardener - HV 953U; Araldite AW106. The Araldite should be applied both to metal and Slideway and be spread as uniformly as possible by means of a serrated spatula. To obtain the best dispersion of the adhesive, when spreading on the surface brush in the longitudinal direction; when spreading on the metal, brush in the transverse direction. The total quantity of bonding should be approximately 200gm per sq. mt.
Hardening: After mounting the Slideway a clamping pressure of between 30-35 Kg/cm2 is recommended. It is important to keep the pressure constant during the hardening process. Due to the differences in the thermal expansion coefficient of the materials, maximum curing temperature should not exceed 40°C. The hardening time for various temperatures is: 20°C min 15 hours; 25°C min 12 hours; 40°C min 5 hours.
Finishing: After curing of the adhesive, the PTFE can be machined by conventional means – if required. The choice depends on the machinery available viz.: grinding; grindstone.
Grinding: For grinding of Lubring use the same speed as grinding cast iron, taking care that sufficient cooling is used with an ‘open ’stone. The grindstone should be preferably silicon carbide based with rubber or polyurethane binding; grain size 80-30. Alternatively aluminum oxide with rubber bonding may also be used for soft, fine grinding action, pre-polishing and pre-mating treatment.
Oil Grooves: Lubring pads can be machined with oil grooves using the same methods and cutting data as used for cast iron. The form and depth of the oil grooves are optional. However, the oil grooves should never pierce through the Lubring Slideway. Oil grooves should be away from the edges by 6mm.
Metal Mating Surface: The metallic mating surface running against the PTFE pad should be preferably Stainless Steel (SS) 304 with a grade #8 mirror finish. Against this material, Lubring will have a coefficient of friction of between 0.1-0.12.

Conclusion
The recent surge in PTFE prices has obviously had a substantial impact on the price of Turcite ® (Lubring). However, owing to the ambiguity surrounding the material’s composition (many clients know it simply as “Turcite ®” and are unaware that it is PTFE based), there has been genuine confusion as to why the price has increased recently. While it take times and patience to convince clients that the price of Turcite ® is governed by the price of PTFE, it does serve as yet another reminder of how an effective branding campaign can truly give a product it’s own identity.
Turcite® is the registered trademark of Trelleborg Sealing Solutions

Monday, May 9, 2011

PTFE Compounds and their effects

We have shifted to www.polyfluoroltd.com/blog - do follow us there

We have spent a significant amount of time looking at PTFE as a material, comparing it to other materials and analyzing its uses based on the various properties it exhibits.
However, our focus has been purely on “virgin” PTFE – namely, PTFE in its pure form. In this form, PTFE takes on an opaque-white hue, is best describes as a soft-waxy material and is smooth to the touch.
Compounding PTFE refers to the mixture of PTFE with additives, which would both add and remove certain characteristics from virgin PTFE. It is essentially a mixture of PTFE with other substances – done for the purpose of enhancing one or more of the characteristics of PTFE, so that the compounded material would be a better overall fit to a given application.
Compounding Process
Before we delve into the various compounds, let’s look briefly at the process behind PTFE compounds.
In truth – most of the large resin manufacturers (DuPont, Daikin, Solvay etc.) have focused on manufacturing virgin resins and left the compounding to smaller companies – who buy the virgin resin and use it in making their compounds. Although the compounder is very much the owner of the product’s quality – it must be mentioned that the input resin does have a huge impact on the final quality of the compounded grade.
For example – we had procured a large quantity of PTFE+Bronze resin from a Chinese company, only to find that when we moulded large pieces from the resin (in excess of 15-20 Kgs per piece) – the pieces would crack during sintering. When we took it up with the supplier, it became apparent that the base resin was of a poor quality, and unsuitable for large pieces.
The compounding process is usually a proprietary technology of the compounder. However, technical literature will point to one of two ways to compound resin:
1. - Physical blending – a physical process, done in an industrial blender where PTFE and the additives are added in the required proportion. The blended powder is then sifted through a mesh to separate the mixture from ‘lumps’ of PTFE that tend to form during blending. The process is repeated until all lumps are suitable removed.

Blending like this is a tedious process, and requires much iteration. Even when care has been taken, small lumps may still remain which will result in patches of white (assuming the blend is pigmented) on the final product.

- Chemical blending – this is more expensive, but also ensures fewer iterations and more uniformity in the blend. A range of chemicals is available for this process – but the basic principal is to have a liquid aid with a lower surface energy than PTFE. This will allow the pigment to flow in between the PTFE molecules so that even the lumps are suitably coated with the pigment.
However, the finer aspects of compounding are usually learnt only through experience and remain a technology that compounders would not part with easily (understandably!).
We have looked at these before from a theoretical standpoint. Some of the properties remain unaffected (or hindered) by the addition of fillers, while others are impacted positively.
Temperature Resistance
It would be sufficient to say that compounded grades have to have at least, if not higher temperature resistance than PTFE – as else they would not survive the sintering process – which happens at 350-400 °C
Dielectric Strength
In most cases, this is only reduced by the addition of fillers – as PTFE in its virgin form shows exceptional electrical resistance. We have yet to come across an application where a filled grade of PTFE is used for purely insulation purposes
Hardness
Being a soft material, the addition of fillers can greatly increase the hardness. This is especially sought after in PTFE components – where the softness of the material can lead to deformation in the long run, affecting the overall assembly within which the component is used.
Coefficient of Friction
Like with dielectric strength, the dynamic coefficient is usually hindered with the addition of fillers. However, because virgin PTFE exhibits significant creep – there is a case for filled grades in applications with minimum movement where a low static coefficient of friction is required.
PV Value
The PV value of a compound is the product of the unit load P (MPa) on the projected area and the surface velocity V. The PV of PTFE is usually enhanced by the addition of fillers.
Wear
In general, the addition of fillers to PTFE resins improves wear resistance but reduces abrasive resistance by providing discontinuities in the PTFE resin which can be entered by sharp practices that may tear the material.
Moisture Absorption
Unfilled PTFE does not absorb water. Filled PTFE compounds absorb small amounts of moisture. Since PTFE resin and fillers are not hygroscopic, any moisture picked up simply fills the voids. Extent of pickup is so small that the dimensional stability is essentially unaltered.
Chemical Resistance
Again – given PTFE is unmatched amongst other materials in its ability to remain intern to chemicals, adding fillers can only reduce this property. However, it does depend ultimately on the application and whether there is a requirement for such a high level of inertness. Typically however, for applications needing this property (medical, labwares etc.) – virgin PTFE remains the preferred choice.
Standard Compounds
Now that we have looked at each of the properties, let’s look at some of the standard compounds and see how each compound alters the characteristics.
Glass Fiber
This is the most universally used PTFE filler and is normally mixed in either 15% or 25% ratios. Glass is itself highly resistant to chemicals and also exhibits very good dielectric properties; add to this the added mechanical properties and creep resistance that it provides and it’s not difficult to see why it is so sought after.
Glass fiber also offers improved wear resistance, but reduces the coefficient of friction. Furthermore, it imposes a higher wear rate on the tools while machining– making it a slightly more expensive material to machine. For the same reason, it is very difficult to ‘skive’ glass filled PTFE tapes to thicknesses of under 0.25mm – as the wear induced on the skiving blade renders the blade dull before a significant length can be skived.
Carbon-Graphite
Graphite is generally used in compounds destined for chemical and mechanical service. Graphite reduces initial wear and provides general strengthening characteristics to the composition. Also, graphite compounds generally display high load carrying capabilities in high-speed rubbing contact applications and exhibits the highest hardness of any of the compounds.
Of all the compounds, we have found Carbon-Graphite to wear out tools the fastest. The same tool that might give 200-300 components if done in virgin PTFE, will only give 15-20 components in Carbon-Graphite.
Bronze
Bronze is usually mixed in a 40% or 60% ratio. Bronze compounds have higher hardness, lower wear, higher comprehensive strength, better dimensional stability, higher thermal conductivity, lower creep and cold flow than most other compounds.
However, test data shows that bronze compounds are not suited to many electrical applications or to those that involve corrosive service environments.
Molybdenum Disulfide
MoS2 adds substantially to the hardness, stiffness and wear resistance of PTFE resins. It reduces starting friction and has little effect on PTFE 's electrical and chemical properties. Generally, only small amounts of molybdenum disulfide are used, most often in conjunction with complementary fillers (usually bronze or glass).
In addition to the above fillers, we have used fillers of ceramic, stainless steel and ekonol. Many branded compounds of PTFE continue to exist (eg: Rulon, Turcite etc) – but a comparison of properties shows that there is little difference between the branded compounds and one of the regular grades.
-----
Ultimately, choosing a compounded grade is a question of application – asking which property needs to be enhanced and which can be foregone (or compromised on). In most mechanical applications, it becomes a trade-off between higher mechanical properties (hardness, wear resistance, creep) and lower coefficient of friction.
It should be noted than very rarely does cost play a huge decider in choosing a compounded grade. While historically, bronze has been most expensive, followed by glass and then carbon-graphite (virgin PTFE has usually been priced around the same level as carbon-graphite) – their properties are so different that the end user rarely sees them as substitutes.
To know more, please view our site: www.polyfluoroltd.com; or view our PTFE (Teflon) Manual

Monday, April 25, 2011

What you need to know about PTFE structural bearings

We have shifted to www.polyfluoroltd.com/blog - do follow us there

Bridges typically consist of two components: the superstructure and the substructure. The superstructure is subject to various dimensional deformations due to the nature of loads placed upon it. These deformations could include:

  • Thermal expansion/contraction
  • Elastic deformation under live load
  • Seismic forces
  • Creep and shrinkage of concrete
  • Settlement of supports
  • Longitudinal forces - tractive/ breaking
  • Wind loads
The nature of these forces makes it necessary to have a device in between the substructure (base) and the superstructure which allows for the required movement, while also giving stability and having the capacity to bear the loads placed on the bridge. The device most popularly used, is a bridge bearing which assumes the functionality of a bridge by allowing translation and rotation to occur while supporting the vertical loads.









Thus, a bridge bearing is an element of the superstructure which provides a vital interface between the superstructure and substructure.
PTFE in Structural Bearings
The use of PTFE in such bearings has been steadily increasing, although its application does not extend to all variants of bridge and structural bearings.
PTFE has an exceptionally low coefficient of friction and high self-lubricating characteristics, resistance to attack by almost any chemical, and an ability to operate under a wide temperature range.
Furthermore, while unmodified PTFE can be used to a PV value of only 1,000, PTFE filled with glass fibre, graphite, or other inert materials, can be used at PV values up to 10,000 or more. In general, higher PV values can be used with PTFE bearings at low speeds where its coefficient of friction may be as low as 0.05 to 0.1.
The low coefficient of friction exhibited by PTFE is unique for two primary reasons:

  1. PTFE against stainless steel exhibits an even lower coefficient of friction that PTFE against PTFE. In fact, the coefficients of PTFE against steel have been found to be the lowest between any two solid materials
  2. The coefficient reduces with increased pressure - allowing for coefficients as low as 0.03 (See table 1)

To summarise, the following properties have driven the increased application of filled grade PTFE:
  • PTFE against steel has one of the lowest coefficients of friction
  • The load bearing capacity of the PTFE sheet is in the range of 130-140Kg/cm2
  • The PV values are found to be in excess of 10,000
  • Service temperatures of -250 to +250°C are possible

PTFE is most commonly used in two types of structural bearings:
Sliding bearings: A system of two plates, one sliding over the other makes one of the simplest types of bearings. These bearings permit translation in longitudinal and transverse directions, unless specifically restrained in any of these directions. No rotation is permitted unless specially provided in the form of articulation and only vertical loads are resisted / transmitted by these bearings.



Generally, plain sliding bearings are provided where span is less than 30m, because the movement capacity of these bearings is usually small.


The bearing is composed of two thick sheets of steel (preferably high-density carbon steel). Between the sheets are one layer of PTFE (with suitable fillers) and one layer of polished stainless steel. The stainless steel is welded to one of the bearing plates while the PTFE is bonded to the other plate. To provide for better bonding, a recess is created on the bearing plate into which the PTFE is fitted.
Their regular maintenance is very important, to keep a tab on friction otherwise the value of horizontal force transmitted to sub-structure will increase tremendously. Therefore, the frequency of lubrication has been prescribed as once in three years.
POT-PTFE Bearings: These consist of a circular non-reinforced rubber-pad (elastomer) fully enclosed in a steel pot. The rubber is prevented from bulging by the pot walls and it acts similar to a fluid under high pressure.

While the bearings were initially created without PTFE, the necessity of horizontal movement in addition to load bearing capacity made it necessary to incorporate PTFE on the piston. The rotation, therefore, is provided by the elastomer due to differential compression and translation by steel and PTFE.
POT bearings offers a much higher degree of movement than standard sliding bearings, although it is tougher to manufacture due to the extended recess needed for the POT as well as the sealing elements needed to contain the elastomer within the POT. These seals must be metallic. The PTFE plate must be recessed into the piston and requires 'dimples' into which additional lubricants are placed during time of installation.

Typical working conditions for standard POT-PTFE bearings include:
  • Provisions apply for temperature ranges of -10°C to +50°C
  • POT bearing of diameter up to 1500 mm are within scope of these specifications
  • Rotation up to 0.025 radians only considered
  • PTFE can withstand bearing pressures in excess of 40MPa - depending on the filler used(See table 2)

Designing PTFE structural bearings
Various design codes exist for structural bearings and most of them prescribe similar materials to be used and have similar requirements regarding the grade and strength of the materials. In India the code book for POT-PTFE bearings is the IRC:83 (Part II) while for sliding bearings, there is no system as yet established in India (although the IRC:83 does refer to the sliding arrangement requirements for POT-PTFE bearings, which can be adopted for all sliding bearings as well). Globally, standards such as the BS:5400 and AASHTO exist for sliding bearings and POT bearings.
Ultimately however, the bearing manufacturer undertakes the responsibility to design the bearings based on customer specifications.